A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
This post below in relation to Tools You Need to Install a New Bathtub is fairly captivating. Read it for your own benefit and see what you think of it.
Setting up a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a new one is additionally a reasonably hard task. If the old bathtub is easily accessible, the project can move immediately; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. See to it you have qualified yourself for the work as well as are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is much better to take into consideration employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This article will assist you set up a brand-new tub in your washroom if you have actually currently gotten a new tub and do not need to transform the setup of your previous supply of water pipelines.
Your devices as well as product list should make up the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are useful in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water as well as check all joints as well as new pipework for leakages as well as tighten them if required. Fill the tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub must wait up until the tub has been utilized a minimum of once as this will resolve it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in place with the producer provided backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bath and also the tiling, bring about difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the market. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that information was worth the trouble. Loved our blog? Please share it. Let somebody else find it. Thank you for your time. Come back soon.
Ready to help! Report this page